Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
In the cs_de.c, we have an IQ pair extracted from remote_pct and local_pct. Assuming this code runs on initiator (where the ranging is done), and remote/local stands for reflector...
I tried to use NRF_SOCK_RAW and NRF_IPPROTO_RAW to create socket, but found `modem fault`!
//this is my wrapper
socket_create ( true , AF_INET , SOCK_RAW , IPPROTO_RAW...
Hi, I very much doubt this is a SoftDevice issue but sticking it out there as an Apple dev asked me. Short story is I have users in production using an App connecting to NRF52810...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to do i2c communication between Renesas...
Good morning, I have built and flashed the l2-e1 exercise on both the nRF5340DK and the nRF54L15DK. When the nRF54L15DK boots, the following output is displayed in the terminal...
Hi,
I’m working on nRF54LM20A and trying to configure the internal capacitors for the 32.768 kHz crystal (LFXO) using the factory trim values in FICR.
According to the...
Hello, read through the documentation about the SAADC and found the TRIM.LINCALCOEFF[n] register. ADC-linearity is important in the project I'm involved in... Seems that the...
Using nrf connect SDK 2.5.0
The nrf device is an L2CAP CoC server. I am using an RPi 4 to test with. The application is for transferring data through UART to another chip...
Greetings!
We have been using an nRF52840 Development Kit for a while now and have been performing FW updates OTA (between the same 3 FW images, cycling and updating between...
I am still on the learning curve of nRF Cloud (and the nRF9151 in general) and am trying to add A-GPS to a project.
Using nRF Connect SDK and Toolchain 3.1.1, I cannot add...
I am using the nRF Connect for Visual Studio Code Add-In running with the nRF Connect 2.5.0 toolchain and was trying to implement the application versioning on a nRF5340 DK...
Hi,
I am working on a project which uses nRF5 sdk v17.1.0 & mbedtls v 2.2.8.2. Now i ma planning to make some changes in application code and re release it. My question...
There appear to be mistakes in haptics_handler.c it appears to be using outdated functions / includes in NCS 3.2.1:
The corrections that work for me:
Changes made: ...
I must have the PPK2 data logger running for too long .because now it won't start. I see the currently available space is 0.0 MB, so maybe that's the problem.. I tried to...
