Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
We are defining a BLE interface for our product, choosing SIG and custom services, and while working on BLE for years now, I have still questions on how to design the...
How to configure the SPIM if i have defined my MOSI/MISO/SCK pins in the device overlay file, shown below:
&pinctrl { spi0_default: spi0_default { group1 { psels = <NRF_PSEL...
We are developing a board with an nRF54L15 module that interfaces with a SPI device. We want to use 3-wire spi, so the MISO and MOSI lines are shorted (according to the datasheet...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2.
I am currently using Pawr. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hello Nordic Support,
Currently, we are using nRF5 SDK for Thread and Zigbee 4.2.0 for our Zigbee coordinator application running on nrf52840.
We understand that this...
I am using the NRF5340 Audio DK , and the onboard PMIC is the NPM1100 . I am not using the onboard audio codec of the DK. Instead, I am powering an external audio codec module...
Hi,
I've just completed Lesson 2 Exercise 3 and found that BLE Provisioning does not work from the iPhone version of the app. The problem seems to be related to Version...
Hi everyone,
Environment:
nRF Connect SDK v2.8.0
Light Switch example
I’m currently working on implementing a Zigbee Sleepy End Device (SED) for a battery-operated...
Hello,
I'm currently using the nRF9151-DK hardware to develop our product based on the nRF9151 SiP . We selected the ncs-serial-modem firmware, and the modem is controlled...
I am implementing the code for nrf54l15 nordic MCU to: Use vbat_mon pin p1.10 in NRF54L15 as ADC and trying to read the voltages, but physically i am not able to read/get...
Hi,
I'm using nrf54l15 SOC with Zephyr NCS SDK to build a BLE application. I want to set the radio Tx Power to be set to as high as possible as our device will be enclosed...
Hi There.
I been 15 year experience in embedded system development but I'm very new to the Nordic nrf environment.
I'm eager to learn and develop some product and provide...
Hi, I have a nrf54H20 board rev 0.9.2 and I followed the https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/app_dev/device_guides/nrf54h/ug_nrf54h20_gs.html#nrf54h20_dk_bring...
Hello, We are currently working on designing a CS-based distance estimation algorithm, referencing the two example routines, `ras_initiator` and `ras_reflector`, from NCS...
I'm getting exactly the same as this ticket now I've switched to extended advertising. Was there any resolution?
Android is fine, iOS 18.5 phone sits in a connect/error...
