We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hello,
I am using the example on the Nordic DK to get UDP messages from the Hologram API to the Nordic Modem. AT#XUDPSVR=1,6002 #XUDPSVR: 3,"started" OK
I very inconsistently...
Hello,
I am working with the nRF9151 board and trying to read SIM/eSIM information.
Steps I followed:
Used nRF Programmer → Erase all.
Opened Board Configuration ...
Dear Nordic
We are evaluating a wearable device and plan to use nRF54H20 be our MCU,
Since our device will be a small form factor and Nordic not released datasheet yet...
Hi, I'm working on nRF9151 on custom board, NCS 3.1.0 and I'm building application with TF-M enabled. I've encountered quite a strange problem. If I remove all UART instances...
Hi,
using nrf sdk connect 3.1.1
using nRF54L15-PDK evaluation board.
Steps to reproduce issue:
1. Setup my board into low power. my branch mark is ~2.9uA.
2. Perform...
I use BLE for one-to-many connections. Usually, the peripheral device should first broadcast, then establish the connection for communication, and finally disconnect. However...
Hello,
We are developing a product based on the nRF54L15, using BT Mesh. We also use the FLPR. For communication between the cores, we use ICMSG.
Separately, ICMSG and...
Hello!
I am completely new to embedded development and i am becoming quite desperate.
I have ordered a custom board which has an nrf52840 chip on it and a vl53l1cxvofy1...
I am using the nPM1300 MIKROE Click board with an ESP32 over TWI (I2C) . I am facing an issue when VDDIO is sourced from VOUT2 using the onboard VDDIO_SEL jumper .
Although...
I have an odd issue with an older nRF52840-DK, I can flash and read memory from the device just fine but no matter what version of NCS I use, it will not execute whatever...
Hello,
I am working on adding MCUboot to my custom board (using nRF52832 chip) to make it DFU-able. That works fine when using internal flash but never when moving the...
Hello, I'm using an nRF9151 DK with an SPI attached SD card and SDK 3.1.0.
SD card is accessed using FAT_FILESYSTEM_ELM.
Using a single thread approach everything is working...
Hi,
We are using a TMD2636 proximity sensor on our board, connected via I²C on pins P0.18 (SDA) and P0.30 (SCL). The same I²C bus also contains a TMP117 temperature sensor...
Hi,
I’ve enabled OTA firmware updates in our project using MCUboot. Before enabling OTA, everything worked correctly—our firmware received interrupts on pin P1.00 from one...
