Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi ! Its me again. I'm using zephyr 3.5.0 via zmk. I'm trying to play a 60 Hz uncompressed PCM file from a wav embedded in flash memory.
I'm noticing some inconsistent output...
I had previously existing firmware that performed a firmware upgrade using mcuboot and dfu_target. This was done over bluetooth but did not use any existing available bluetooth...
Hello,
I'm trying to build my program for a custom board with FOTA BLE.
Im using v2.9.0 for the SDK and the toolchain. The custom board has a nrf52832.
When building...
In the 'nRF91 Series Antenna and RF Interface Guidelines' document there is a section ' 4.3.1 Combined GNSS and LTE antenna example' which shows a potential way to use a single...
Hi everyone,
I have an nRF9151 connected to an nRF52840/(or nRF54l15) over a single UART . I want to:
perform DFU of the nRF52840 from the nRF9151, and
also...
I am currently working with the Channel Sounding sample on the nRF54L15 DK boards (SDK and toolchain v3.1.1) and using Nordic’s multiple-antenna support as described here...
Hi,
I have a general question about the GRTC accuracy on nRF54L15.
In the manual it states the following:
We will like to use the GRTC as timekeeper with an external...
HI all,
I'm working on a firmware for the nRF9151. In the development desk all works good. But under release conditions the software crashes cause of locked RAM access...
After using the official example hci_uart with the nRF54L15-DK, it is configured as an HCI controller. I used bluetoothctl commands like scan on and connect to scan for peripheral...
I'm leveraging a fuel_gauge example to pass a version string as part of a Device Information Service. When viewed in Nrf Connect (desktop or mobile) only the first character...
Hi,
I tried to build and flash the binary of NRF WiFi Course Example L2 E3.
There was no build and flash error. But there is no logs on both UART terminal.
My setup...
Hi Nordic Support Team, I'm experiencing severe memory constraints with the AWS Io T Core example on the nRF 7002DK (nRF 5340) that make it impract ical for real-world applications...
Hi, we are using the nrf_cloud_fota_poll library with CoAP to interface the nRF Cloud for FOTA updates for nrf9160.
In lossy mobile network with bad reception, the FOTA...
Hi,
Developing with nRF54L15-DK on Zephyr RTOS, our team concerned about nRF54L15 DK board maximum advertising range.
Is there any Bluetooth performance report to show...
Hi Support Team
Customer's end product needs to test in MRI when the product is completely powered off. Customer concerns that the following three components will be infected...
