Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I am working on a school project and need to set up SPI communication between a wiznet,W5500 and the nRF54L15DK. I can build and run my program but I am getting no responce...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello,
With NCS v 3.2.1, I am working on a BLE application with nRF52840 dongle.
I was trying to add FOTA feature in my application by adding the following line to sysbuild...
I just ordered and opened up the nRF9160 dev kit from Digikey. I was going through the quick start and I named the device and when I went through the verification step, it...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We have a Thingy:91 (nRF9160) that we use for various LTE-M / NB-IoT network debugging. Until recently I was able to see both RRC and NAS messages in both " Cellular Monitor...
Hello,
I am developping an application based on ESB protocole using BT840NE module (nrf52840 + nRF21540) SDK 3.2.0.
on the PTX side, I am measuring the current using the...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
When updating from nRF connect SDK v3.0.1 to v3.1.0 we noticed a change in the clock_gettime() function.
In the old version, the clock was not reset by a reboot.
The new...
nRF5340 I2S MCLK issue – unable to get 12.288 MHz MCLK for 48 kHz sampling
I am using the nRF5340 SoC and configuring the I2S peripheral as Master to achieve a 48 kHz audio...
Hi,
I get a PCBA which contains the following test points of nRF54L15 : P0.02, P0.03, P2.07, P2.08. I would like to set one of them to be UART TXD.
In pin assignment...
hi support team,
customer is using mesh and met a problem, here is the situation:
1. customer using mesh/light as basic demo, adding mesh DFU function in it ,and deploy...
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
Hi,
I purchased several nrf54L15 development boards and am preparing to...
I'm trying to run a custom image on the net core. I've successfully done so using the following exercise in the intermediate course: lesson 8 exercise 2 however when trying...
