Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I'm trying to use the bitcounter to drop packets that don't comply to a specific UUID. I'm working with nrf52840.
My question is - if the received packet is shorter...
If a device has established a PDN connection, is it sufficient to rely on lte_lc's pdn module to determine if a network connection has "failed" due to being out of range,...
Nordic Team:
We have a product in production that uses the nRF9160 and nRF7000 and had assumed the nRF7000 did not transmit. We only recently discovered that it does, in...
Hi
How can I use ztest to calculate code coverage on the nrf54l15 platform, I tried to use the configurations of CONFIG_FORCE_COVERAGE=y, CONFIG_COVERAGE_GCOV=y, and CONFIG_COVERAGE...
Situation
When using vanilla zephyr I get a very verbose generated zephyr.dts file where every line is annotated with the line's origin like the following:
However,...
I am using Wireshark with Nordic BLE Sniffer plugin. The sniffer dongle used is nRF52840. I using it to capture a BLE connection from my laptop BLE to a peripheral BLE device...
Hi
I would like to synchronize multiple devices over wifi.
Over BLE and NRF I see the posts using time slot spi. Is there any way to do this over WIFI?
I found this...
i found [A1A] build code on real device which in hands.
but we can not find [A1A] information on devzone, as of 2026 Apr 25th.
could you let us know more detail of [A1A...
Hello Team,
I am facing strange issue in VS Code. Previously I had installed nRF Connect SDK v3.0.0 and later I did uninstall it.
Today I was trying to install nRF Connect...
I used nRF52840 with nRF5 SDK 17.1.0
Also use freeRTOS from example "ble_app_hrs_freertos"
I need implement System-On mode deepsleep mode. So I use nrf_pwr_mgmt_run...
Hi, based on the nRF5340 Audio DK (nRF5340_AUDIO example: gateway, BIS) we send an LE Audio Stream.
As transceiver we use an Airoha AB156x based speaker: SoC name : ab156x_evb...
For just a first test board off of Thingy 91x design, can nRF5340-CMAA be replaced with nRF5340-CLAA? What's the downside of doing that? Documentation says it's not recommended...
Context : I'm building an embedded application using the nrf52832, that can turn on/off and be configured via NFC. These functionnality are implemented using the t4t library...
Hi,
We are working on a project in which data must be sent to server using NB-Iot.
We are struggling establishing an HTTPS connection with a server using the NRF9160 development...
I'm trying to slim down my application to fit in an nRF52832 (currently overflows RAM when building) so I'm carving things out using the prj.conf file. But I'm running into...
