Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi all,
I am wondering if it is possible to implement SHAKE128 and SHAKE256 (FIPS 202) via the CRACEN hardware accelerator on the nRF54L15. Looking through the nRF Connect...
I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
While researching a host of topics, I have noticed that there is a concerning number of dead links and missing documentation. In 50% of cases, the links from Google search...
Hi
I have a question regardin why nRF54L15 cannot use the automatic mpsl power split?
If I want to use ESB + nRF21540 with automatic TXP control, what should I do?
Hi all,
I recently updated all Segger JLink software using the Segger download links and updated the probe as prompted by VS Code NRF Extension. Up until about two days...
Hello, I am currently using the nRF9151 LACA A1A SIP module for the development of NTN communication application terminals. In my hardware design scheme, the nRF9151 module...
Context: I am making sample apps on the nRF54LM20DK ver 0.3.4 on ncs 3.2.1. I noticed that when trying to use the built in PWM shell that 100% duty cycle is not being set...
Hello Nordic team,
I am using the nRF54L15 QFN with Bluetooth Channel Sounding.
Channel Sounding is already working in my application and is useful for warehouse object...
Hello,
We have set up our nRF91 based devices, to use the nRFCloud for the data transfer and also to manage FOTA, in our fleet. Using the nRFCloud firmware updates feature...
Hi,
1.The customer does not require an external hardware reset circuit. How should the reset pin be handled externally?
2. Can R1 and C13 be omitted?
3. If R1 cannot...
I run a large research lab using hundreds of nRF52840 DKs. These boards are periodically rotated between active experiments and storage. Because boards are pulled from storage...
Hello,
We are currently performing power consumption measurements on the Nordic nRF9151 using the PPK2 in LTE-M with an Objenious SIM card.
During our tests, we observed...
Hello, We have registered our project with Nordic. Our project ID is 60803622472. Project title: DECT NR+ Star Topology Sensor Node Evaluation with nRF9151 We would like to...
Hi Nordic team!
I haven't been able to implement the joiner functionality on a Thread network with nrf52840. I'm using the nRF52840-DK as the leader. For the DK, I follow...
Hi all. I am testing the NPM1300 with nrf54l15 using vallina Zephyr. I've setup device tree for npm1300 to generate interrupt on its GPIO0 when there is event.
When Vbus...
