Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I found a issue, I open a sample project " v2.5.0\nrf\sample\cellular\location"
when I click "Add build configuration", no nrf9160 option and only nrf52840 can be selected...
Hi, I am trying to do pwm a rgb led using nrf54l15dk and custom board using nrf54l15 on port1 with pin connections on (p1.10, p1.8 and p1.13 for custom) or on (p1.11, p1.12...
Greetings,
I have worked with the MCUBoot and its Serial Recovery feature with success and recently tried to enable the CONFIG_BOOT_SERIAL_WAIT_FOR_DFU option ( as well...
Hello,
I am intending to extract audio from the onboard microphone of nrf5340-audio-dk.
I used the nrf5340_audio application as reference but cutting off the bluetooth...
Hi,
I'm trying to use same UART channel on both project-specific purpose and MCUmgr DFU. However, when I enable the option CONFIG_MCUMGR_TRANSPORT_UART, the code reset's...
Hi, I used in my hw design Config. 6 for nRF52840 QIAA aQFN73
https://docs.nordicsemi.com/bundle/ps_nrf52840/page/ref_circuitry.html#ariaid-title7
The question is how...
Hi,
We are defining a BLE interface for our product, choosing SIG and custom services, and while working on BLE for years now, I have still questions on how to design the...
How to configure the SPIM if i have defined my MOSI/MISO/SCK pins in the device overlay file, shown below:
&pinctrl { spi0_default: spi0_default { group1 { psels = <NRF_PSEL...
We are developing a board with an nRF54L15 module that interfaces with a SPI device. We want to use 3-wire spi, so the MISO and MOSI lines are shorted (according to the datasheet...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2.
I am currently using Pawr. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hello Nordic Support,
Currently, we are using nRF5 SDK for Thread and Zigbee 4.2.0 for our Zigbee coordinator application running on nrf52840.
We understand that this...
I am using the NRF5340 Audio DK , and the onboard PMIC is the NPM1100 . I am not using the onboard audio codec of the DK. Instead, I am powering an external audio codec module...
Hi,
I've just completed Lesson 2 Exercise 3 and found that BLE Provisioning does not work from the iPhone version of the app. The problem seems to be related to Version...
Hi everyone,
Environment:
nRF Connect SDK v2.8.0
Light Switch example
I’m currently working on implementing a Zigbee Sleepy End Device (SED) for a battery-operated...
Hello,
I'm currently using the nRF9151-DK hardware to develop our product based on the nRF9151 SiP . We selected the ncs-serial-modem firmware, and the modem is controlled...
