Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
# Background
I am attempting to install ble-sniffer onto WireShark for BLE sniffing. I have been following the guide in Link. I have already flashed my nRF52840 USB dongle...
Using Thingy:53, I needed to add the following code to the boards/thingy53_nrf5340_cpuapp_ns.overlay file in order to be able to view the output:
&uart0 {
status="okay...
Hi
We measure I2C SCL falling time is 5.87ns, little faster than spec. 6.54ns ( 20*1.8/5.5)
We use PIN_CNF[n] (Address offset: 0x200 + (n × 0x4)) ID D drive to tune, but...
Hello,
Are there schematics available for the nRF9151DK?
In the hardware ZIP file, I can only find the BOM and PCB files (PcbDoc and PrjPCB), but no schematic files or...
I want to design a pair of TWS speakers using the nRF5340, but I'm having a hard time figuring out where to start. From what I understand, the unicast server nRF5340 audio...
Hello Nordic Team, I have devices running nRF9160, modem firmware 1.3.6, tied with MNVO SIM card that provide access to multiple operators. Providing an example seems to be...
Hello Nordic Team,
We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces .
We have...
Hello, I observed that under low-throughput conditions (2 kbps), the power consumption of the nRF21540 combined with the 54L15 (at 20 dBm) is actually lower than that of using...
Using the Zephyr HCI_UART sample, configured and built for an nrf54L15 DK, with version 3.2.1 of the SDK, I get an HCI error 7 (Memory Capacity Exceeded) when attempting to...
Hello Nordic Team,
We are working with the NRF5340-QKAA-R7 and need clarification on which physical pins can be used for UART, I2C, SPI, PDM and USB interfaces .
We have...
Hi，
During the initial screening of Matter certification during the R&D phase, it was found that several test items did not pass the test. Could you please help investigate...
