Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
During design and schematic entry I used the online datasheet to select GPIO capability. I was advised that I should try out the pin planner to confirm that pin choices...
I am using the nrf_fuel_gauge_idle_set function to handle the fuel gauge state when the system enters a low-power mode. When the charger is connected, I exit this state and...
Hello Nordic Support Team, I am experiencing an issue when using MQTT over an NB-IoT connection with the nRF9151 DK, and I would like to ask for clarification and guidance...
Hi,
I am working on a Matter device based on Nordic NCS v2.9.0, using Google Home as the OTA provider.
I have successfully uploaded a new OTA image in Google Console,...
n the nRF52805, if the hardware is configured for DC/DC regulator operation—namely, with the DCC and DEC4 pins connected through the designated inductor and capacitors—does...
I am using a Thingy91x, with some additional sensors attached via qwiic cable.
Initially to test the Thingy91x I inserted the SIM and scanned the QR code on the Thingy91x...
I am developing a proof-of-concept for remote controlled super-low-power devices using PAwR. I started with nRF52840 (for boths, clients and remote) and now migrated my code...
I built and ran the Matter Light Bulb example for Thread and was able to commission it into Home Assistant with no issues. However, when I tired the Matter Temperature Sensor...
Hi
Setup: nPM1300, nRF54L15-based board, SDK 2.9.2
I am trying to figure out how to use the nPM1300.
So far, I have not succeeded. Quite frequently, after power...
Hi,
I downloaded the NCS v3.2.0, but always got the error below when u npacking the toolchain , the same error when downloading via Vscode. and there is no problem for v3...
Hello all, I am using the nRF52840 together with the nRF7000. To save GPIOs, I would like to use the BUCKEN pin (which is directly connected to the nRF7000) also as the enable...
I tried to compile the project according to the link（ https://github.com/nordicsemi-neuton/nrf-edgeai-thingy53-ble-remotecontrol ）, but the compilation failed.
The compilation...
Hello Nordic Community,
I am working with the nRF5340 SoC as the master and trying to configure a PDM microphone . I have two related queries regarding PDM/DMIC operation...
I use the nRF5 SDK for BLE peripheral development based on a keyboard example. After the peripheral connects and bonds with a central device, I can detect button presses....
Good afternoon,
I am trying to set up FOTA update over NB-IoT, my device is offline most of the time and connects only a few times a day.
1. What are the gudielines...
