Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
in Memfault I see the device ID number for each device such as 41EF6BB8FB6C9AF9. Is the distribution for the first 3 bytes the same as the distribution for the last 3 bytes...
Hello! I'm using Zepyhr OS with nrf connect SDK v3.2.3 and the NRF54L15 hardware.
I am using UARTE with the async driver (direct memory access). This is my uart configuration...
After a full consume of an spsc_pbuf , the buffer can become logically empty while rd_idx and wr_idx both remain at a non-zero offset. This breaks the next large allocation...
Dear Team,
We are currently using the nRF52833 as the BLE advertiser (cattle node) and the nRF5340 as the BLE scanner/gateway. The system is based on BLE Extended Advertising...
Hi,
I migrated my software from SDK11 TO SDK17
(Changed the BL + SD + APP)
Now i want to upgrade to (SDK17) old units (with SDK11) in the field.
Do you have any advise...
Hi There,
I am currently developing an LTE-M application on nrf9151 using ncs v3.2.1, the device is a MQTT client that publishes telemetry periodically every 3 minutes,...
I'm using nRF Connect for Desktop on Linux and updated today to v5.3.0.
I have J-Link V9.24a installed and it is available in $PATH. Also it works well with Programmer v4...
Hello, My nRF54L15-DK has suddenly stopped working, and it appears to have a hardware-level power failure.
The board was working normally the previous day while running...
We have designed a custom board around nRF54H20 EngC revision and testing it on NCS 3.1.1. We were able to do provisioning and bring up using iron-side binaries. But got two...
Hello,
I am evalating the nRF9151-SMA-DK with a Monogoto SIM card that uses Skylo NTN connectivity.
I am able to reach the internet, since DNS resolution works:
...
Hello,
We are using a custom board based on the nRF5340 + nRF7003 Fanstel module with NCS SDK v2.6.2.
Our application uses MCUboot with dual-bank OTA updates. The secondary...
Hi, I'm using a WisBlock setup with: • RAK19001 base board • RAK4631 core RAK18030 microphone in IO slot A • RAK15002 microSD in IO slot B I'm running Zephyr / nRF Connect...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Hi,
BLE throughput differs between NCS v2.6.0 and v2.9.2. v2.9.2 appears to have fewer MoreData packets. (Both have CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT set to...
Hi, Team:
I want to make an LED blink during OTA upgrade and stop blinking after upgrade.
How do I configure prj.conf, sysbuild.conf, or provide some demos
Thank you...
