I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hi, I'm struggling to setup an application on the nrf54l15dk to control the nrf9151dk SLM over UART.
I have done the Cellular IoT Course and successfully controlled the...
I'm trying out the GNSS sample for the nRF9161 DK. I am trying to enable minimal assistance, but I get an error message with error code 65536: *** Booting nRF Connect SDK...
Hi,
Can MCUboot be used as a second stage bootloader (an application from the Secure DFU Bootloader over Serial Link standpoint) to be DFU'ed to existing devices which now...
Is it possible for users to regenerate the nRF9160 GNSS factory almanac data from public sources?
https://github.com/nrfconnect/sdk-nrf/blob/main/samples/cellular/gnss...
Hel lo, I am us ing a custom nRF5 2832-based b oard that has no DCDC circu itry (LDO onl y). What happened in NCS v2 .5.1
After power-on, the system did not st art (e...
Hello,
I am trying to measure a fast, impulsive signal from an amplified analog microphone using an ADC pin on the nRF54L15-DK. When I read the same signal using a 12-bit...
Our production facility has some concerns about using the OTP parameters. Specifically, they are concerned about writing the wrong value and then needing to scrap the device...
Hi,
We are developing a product based on nRF5340(ncs 3.1.0) and using MCUboot for OTA updates of both app core and net core.
During an OTA update, the following issue...
Hi Team,
I am working with nRF5340 and have a few clarifications regarding SWD protection (APPROTECT / ERASEPROTECT).
While the application is running, is it possible...
We have an unusual issue.
We are using the nrf 17.1 SDK for a custom board with the nrf52840 in tickless idle mode (RTC1) - using the available port_cmsis_systick.c for...
Hi there
I'm using the HCI UART bridge from NCS v3.2.1 in zephyr/samples/bluetooth/hci_uart with the provided overlay-all-bt_ll_sw_split.conf on an nRF54L15Dk and our Bluetooth...
This is just a request for an update to some documentation.
If you do a web search for "nrf NSIB" the first page this is likely to show up is this one . It's a good page...
Hi devzone team I'm working on the nRF54L05 with the FEM RFX2401C from Skyworks. I'm trying to configure the FEM with the "Simple GPIO" option. Here my overlay file:
After...
I have a problem which seems similar to this one: https://devzone.nordicsemi.com/f/nordic-q-a/106158/zephyr-os-ble-central-multiple-notification-subscription-event-issue ...
I'm using the peripheral_lbs sample for testing with the PPK2 kit and the 1.0.0 nRF54L15-DK.
I have disabled logging and serial and added PM_DEVICE and PM_DEVICE_RUNTIME...
