Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I have an NRF52840 dongle programmed with the connectivity firmware and I want to use it as a central device to connect to a peripheral, and I want to set this up in Python...
HI,
I’m working with the nRF21540 and want to add a GDT, a series capacitor and a TVS diode to its antenna port to protect it against lightning surges and ESD. Could you...
Hi
I'm currently in the middle of porting our board from nrf sdk 2.6.1 to nrf sdk 3.2.1. I made it so far, that the correct dts are used, but somehow the build process seems...
I am following the instructions as per Getting Started with the Asset Tracker Template.
I have successfully created the environment and done the West Update.
When I do...
Hei,
I have nRF9151 SMA DK v0.9.0 running with board controller FW v1.1.0. This is stated by the Board Configurator v1.1.2 tool.
I tried to set both nPM VOUT2 and VDD...
Hello,
For my project I am interested in performing IQ sampling in the payload of a BLE packet, using nRF52833 at both receiver and transmitter.
I am manually configuring...
Hi,
We've been developing a product using nRF52840, where it does a lot of advertising and scanning.
We've migrated from SDK v2.5.2 to v2.8.0, and recently discovered...
nRF Connect SDK v3.2.1 on Windows 11
I am trying to build the Matter Light Bulb sample using a nRF7002DK but run it over Thread instead of WiFi (the default). Since this...
Good day,
When using the bt_gatt_discover() with a NULL UUID parameter, the code sweeps all UUIDs available from the start_handle to the end_handle. This is verified with...
Development environment: MacOS Sequoia (15.4.1), Visual Studio Code v1.108 0, nrfConnect 2026.1.1242
I am trying to develop a "workspace" project with a nRF52840DK as my...
I understand that the rf path should be 50 ohm coplaner to the output matching network that should be placed very close the the NRF chip. The recommendation shown in the reference...
I’m facing a Power Profiler Kit II (PPK2) measurement discrepancy that appears to depend on the host PC , not the target board or firmware.
Target setup
Custom board...
Hi all,
What is the increase in current consumption or power consumption when measuring RSSI with the nRF52833?
My device is a peripheral. I would like to estimate this...
I am using nrfx_nvmc_page_partial_erase_init() and nrfx_nvmc_page_partial_erase_continue() to erase flash in-between wireless connection events. The datasheet states: " The...
I have an IoT project that reads data from a proprietary device via an I2c SBIffer. The device consists of a controller and a small display, which are connected via an I2C...
