Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am unable to see any options on the welcome menu for nrf connect
The menu was working yesterday,
I have uninstalled and re-installed and tried a previous version.
...
Hi,
we're developing BLE sensor platforms with 10+ sensors on a device. We have some bandwidth issues if we connecting more than one BLE device to a BLE host:
For Example...
I am using the IQ values collected from the Channel Sounding example. The data in the 0 section seems to indicate that this channel is not in use? For example, as shown in...
Hi, I see this goes back at least as far as v2.4.4 and still exists in v3.1.1. Around line
if ((!err) && (err != -EALREADY)) { LOG_ERR("Stop LE scan failed (err %d)", err...
nRF52840 datasheets says it supports 3 SPI slaves, but I need 4 SPI slave devices on my next design (the current design uses 2 SPIs). I don't need DMA transfer at this moment...
I am trying to implement Attribute caching as described in Vol 3, part G, section 2.5.2 of the Bluetooth Core Spec .
Reading the GATT Database Hash seems to work:
The...
Hi Nordic team,
I’m working with an nRF9160-based device and have observed inconsistent LTE behavior when the device operates in areas with poor or unstable signal strength...
Hi,
I want to synchronously get data from different nodes.
Can BLE mesh obtain information from multiple nodes simultaneously? I would like the collected data to have...
Hello,
Using nRF Connect vscode extension, vscode is very slow and almost unusable.
The following process is started multiple time and i have an instance taking 100...
I have an issue with the Lightness setup server set cb being triggered without a connected device and is not internally called in my code. Yet for some reason the set cb is...
Hi
I noticed nordic provides Wi-Fi: Throughput to evaluate the throughput when device is working in STA mode.
If I want to evaluate the device in AP mode, is there any...
Hallo, we are evaluating the UART peripheral of the nrf54l15. As a first step, we are trying to get two DK to communicate with each other, unfortunately without success. ...
Hi all,
I'm looking at an issue and I can't get my head around it. I clearly do something wrong here but I'm stuck.
On our nRF54L15 DK we have a program that can show...
Dear Teams,
I’m using an nRF9151DK board running a simple firmware (example link: github.com/.../ subsys /pm/ device_pm ).
I connected a Power Profiler Kit II (PPK2) to...
