Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
I've made an Excel sheet to estimate the power consumption for my nRF51822 device.
Modify light-green fields, to fit your design and see what the estimated current is.
Please...
Hi,
1. I tried flashing all ble codes to my nrf kit. It does not seem to connect on Windows machine but connects on Mac. My other nrf kit connects perfectly fine. What is...
Hi,
I was wondering what I need to do, or if it is even possible, to debug a non-secure app which uses TFM.
Running 'west debug' on e.g. the blinky sample works regardless...
I’m running a self-built BLE application on the nRF52DK board. It used to work fine before, but recently it has stopped working. The board still runs all the sample codes...
Problem : I am following on Bluetooth Fundamental Course on Nordic Academy webpage. I successfully advertising BLE with non-connectable option. But change adv_param to BT_LE_ADV_OPT_CONN...
Hi there,
I have implemented the ability to pair the BLE peripheral in our app. However, some users may prefer to connect via IOS settings.
I have seen a thread which...
Hi ! Its me again. I'm using zephyr 3.5.0 via zmk. I'm trying to play a 60 Hz uncompressed PCM file from a wav embedded in flash memory.
I'm noticing some inconsistent output...
I had previously existing firmware that performed a firmware upgrade using mcuboot and dfu_target. This was done over bluetooth but did not use any existing available bluetooth...
Hello,
I'm trying to build my program for a custom board with FOTA BLE.
Im using v2.9.0 for the SDK and the toolchain. The custom board has a nrf52832.
When building...
In the 'nRF91 Series Antenna and RF Interface Guidelines' document there is a section ' 4.3.1 Combined GNSS and LTE antenna example' which shows a potential way to use a single...
Hi everyone,
I have an nRF9151 connected to an nRF52840/(or nRF54l15) over a single UART . I want to:
perform DFU of the nRF52840 from the nRF9151, and
also...
I am currently working with the Channel Sounding sample on the nRF54L15 DK boards (SDK and toolchain v3.1.1) and using Nordic’s multiple-antenna support as described here...
Hi,
I have a general question about the GRTC accuracy on nRF54L15.
In the manual it states the following:
We will like to use the GRTC as timekeeper with an external...
HI all,
I'm working on a firmware for the nRF9151. In the development desk all works good. But under release conditions the software crashes cause of locked RAM access...
After using the official example hci_uart with the nRF54L15-DK, it is configured as an HCI controller. I used bluetoothctl commands like scan on and connect to scan for peripheral...
