hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Since about a week or two ago, I cannot flash (or debug/reset etc.) my device from the VSCode nrfConnect extension, when more than one device is connected to my PC. I am using...
Hi,
I am trying to confirm whether nRF54L15 as a chip officially supports the UTP OTA feature.
From the SoftDevice Controller documentation I can see that the following...
I am using the Zephyr SPI driver to control a WS2812 LED strip through the SPI interface. Since only the MOSI line is required for communication, I want to configure the SPI...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
I make a ble hid usb dongle with ncs2.0, ble keyboard send keycode to hid dongle, hid dongle send the keycode to computer.
When keyboard send keycode slow, it's work fine...
Using 54L15 DK for testing. Zephyr toolchain & SDK both v3.02. I have been through the DevAcadamy exercise which uses Blinky for its example, now I want to integrate into...
Hello,
I need help regarding flash memory read on nRF52840 device, SDk16, SD=340.
I have using the fds libarary for memory read/write in my code for many years now. However...
Hi,
I'm trying to scan for coded phy devices with the nrf-sniffer application.
Followed the guide and installed nrf-sniffer with the nrf-util.
In Wireshark it works...
We are using firmware 1.3.6 on the nRF9160. During testing, I ran into the reset loop restriction. To quickly get out of it, I issued a AT%XFACTORYRESET=0 command. (We are...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to use Wi-Fi (nRF7002) Wi-Fi scan, Wi...
Hello! I am trying to upload the basic applications to the Thingy:91 X from the downloads tab, here: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
I just noticed that there's another issue with my project after upgrading from SDK 2.3.0 to 3.1.1.
I am using the 802.15.4 radio for low level packet communications...
Hi,
for a project based on the nRF54L15, we are evaluating the new single-slot DFU mechanism.
Using NCS v3.2.1, I am testing the sample available at: https://github.com...
Based on the DevAcademy here is my following setup using a custom NRF54L15 chip with the NRF54L15-DK devicetree with following overlay:
prj.conf:
CONFIG_GPIO =y
...
