When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
I did not get Audio - adc value shows zero all the timse why ??
const codec_register CODEC_DEF_REG_DATA [] = {
// ==========================================...
Summary
With CONFIG_OPENTHREAD_BORDER_ROUTING=y (the default selected by CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y ) and CONFIG_OPENTHREAD_TREL=y (also the default), the...
I'd like to know more about the single-antenna AUX functionality of the nRF9151. More specifically, this line in the documentation for AUX has piqued my interest:
When the...
Hello,
I am attempting to develop an open source nRF52832 PCB design, aiming to minimize the footprint as much as possible.
Thus, I attempted to cramp as many components...
I had one nRF54l15-DK,and I want to make a music player by nRF54l15's BLE,but I am not sure is it supposted LE audio to client my headphone.if it supposted, is it full LE...
I am new to nrf52832 development. The question is that:
I want to do m ultichannel(4 or 5 channels) ADC in scan mode every 1s. and the MCU consumes ultra low current(3-5uA...
As the subject suggests. It is a simple question. I only see development boards with NRF53, but we decided to go with NRF54 in this project. We need BLE and WiFi on the device...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi all,
I am using a tagconnect cable to flash my custom boards using a devkit. I was able to flash 4/5 boards. I first recovered the locked factory boards, and then flashed...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
Hello,
I am working with the nRF9151 DK and NCS v3.3.0 . I am experiencing a critical modem fault at startup.
Problem Summary: When I start debugging, I immediately get...
I attempted to conduct Bluetooth development using the nRF52840DK (NCS 3.2.0), but I encountered an MPSL error:
ASSERTION FAIL [0] @ WEST_TOPDIR/nrf/subsys/mpsl/init/mpsl_init...
Hello,
I am trying to add different ConcentrationMeasurement cluster types to my application (CarbonDioxide, VOC, Pm1, etc.) but have an issue with zap-gui not saving the...
