Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
i want/need to connect & access a microSD Card (32GB) on an breakout board via SPI (technical reasons) and want to use the suggested PINS (28-31) as in the intermediate...
Hi Everyone, I am trying a very simple task of reading PDM Mic with NRF54L Custom Board and streaming the Audio via Bluetooth. I was able to do it very easily with the NRF52840...
Hi： Could you please advise me on how to use P1.01 as the output pin for PWM for NRF54LM20A? I attempted to use the regular IO mode and pulled P1.01 to a high level, but when...
Dear Technical Support Team,
I am currently developing a Matter product using the NCS (nRF Connect SDK) version 3.1.1 . During the build process, the software version string...
Hi Nordic Team,
When using the nRF5340 with XIP enabled, a release build with -Os runs perfectly, but a debug build with -Og crashes on the first function located in the...
Here is a properly structured issue report in professional English.
Project ID
SOFTUART-NRF52-19200-RTT-DEPENDENCY
Subject
Soft UART at 19200 baud works only when...
Issue
When attempting to connect GitHub Copilot to the public MCP endpoint `nordicsemi.mcp.kapa.ai` (as described in the [Kapa.ai MCP integration docs]( docs.kapa.ai/.....
Hello all,
I am investigating the feasibility of building an ultra-lightweight, single-use BLE tracker for short-term insect tracking. Target constraints: - Total weight...
Hi, I am testing the Nordic samples for different environments, and started noticing this strange thing, that sometimes the data output is the same as the previous output...
Hey,
currently I am testing FOTA and it works. The only thing I don't like is the fact that
takes > 10s to appear. Is there a way to make it faster? Because most of...
Hey.
We designed custom PCB board (basically an humidity sensor) with Nordic IC. It works fine, but when I did current measurements I noticed that in advertising mode, uC...
Hi everyone,
I believe that the documentation has an off by 1 error. "The MTU includes the SLIP encapsulation, which means that the maximum data size that can be sent is...
The nRF54L porting guide ( link ) states that:
> High speed read transfers use hardware-enabled delay sampling and require resetting the pad configuration between reads...
Adding long path/filenames to the drop-down fields in "Edit Build Configuration" dialog in VS Code Extension leads to hidden buttons (Browse). No additional files can be added...
Hi,
I am writing to inquire about the MTTF, MTTFd, MTBF and/or FIT value of the nRF52840. nRF52833 and nRF52832. Where can I find these values?
This question has been...
