hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I'm migrating an ANT+ BPWR application from **nRF5 SDK** to **NCS v2.5.1** but cannot install the sdk-ant module.
**Background:** - Previously used nRF5 SDK with...
Hello,
I send a ticket because I have an issue to access and write files to a SD Card with NRF54L15DK and 3.1.0 SDK and toolchain.
Can you help me please ?
Here is my...
Hello,
we are trying to run Gazell samples on the nRF54L15-DK, but the protocol & board combination doesn't seem to be supported by version 3.2 of the nrf Connect SDK...
We would like to synchronize several Nordic thingys 53. The Approach is to send two timestamps from a central to them (peripheral) via Bluetooth Low Energy with 100 ms delay...
Hi
I try to start with ST7789 display on nRF54L15 and there are bus fault after add LVGL library. The project is building correctly, but stop just after leave bootloader...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
We are using the nRF9151 with modem firmware v2.0.4 and would like to perform TX RF testing on NTN bands 255 and 256.
TX RF testing is currently initiated using the modem...
I am working on a project where we are sending data to a remote device as fast as possible. The sender will call bt_gatt_write() until it blocks the thread. So it is just...
Dear Sir/Madam ,
I am writing to request a review of the attached schematic. Please let me know if you have any questions, concerns, or suggested revisions.
If possible...
I am in process up migrating a legacy project from SDK v2.4 to v3.2 and going through each revision incrementally to catch all the changes needed to modernize it and maintain...
I have built and flashed both the exercise and the solution. However in both cases I am getting a connected and then disconnected ( Reason 42). I am clueless as to what is...
Hello.
I am currently testing nRF Cloud and encountering an issue. In the "Select a Project" menu, the "Create Project" button is disabled.
Here is some additional context...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
While running scan & connection tests with NCS 3.2.1 , I encountered frequent connection timeouts ( bt_hci_core: Connection creation timeout triggered ) when using the Nordic...
