I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hello,
I have a few questions about the nRF9151 DECT NR+ modem.
I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hello guys,
Im developing RTLS with DWM3001C and right now Im working on personal tag powered by CR2450. So naturally, power consumption should be as low as possible....
Hello.
Are you able to give any specific details around an SDC Assertion with File ID 13 and Line 451 please?
The nRF Connect version is v3.2.4.
I'm trying to isolate...
Hello,
I am currently optimizing the power consumption of an nRF54L10-based project.
While I know that system-off mode is the most efficient, my current implementation...
Hi,
Customer using nPM1300 would like to know what are the minimum and maximum values of Rshphld? These values are not in the datasheet.
Best Regards,
Nic
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
We are trying to understand whether it is possible to use our external flash drive at45db641e to implement DFU and then load the application firmware via Bluetooth. As far...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hello, I am currently developing UART communication firmware for the nRF52805, but I am encountering issues with performing DFU firmware updates.
Below are the details of...
Hi,
I'm reading 1 byte of data from a Macronics MX25R64, but the execution speed of the read operation varies depending on the SDK version.
With SDK 3.1.1, it's possible...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
