I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
1. development environment:
software ncs3.0.1 , DW3xxx_XR6.0C_24Feb2022, vscode
hardware: nrf52840, DW3210
DW3210 is a UWB chip produced by Qorvo, and its corresponding...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
hi support team,
i have close this ticket:
but i need open this ticket and ask how to program 9151 externa; spi flash.
i don't know if 9151 json file is correct and...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Here’s what to check next for toolchain detection issues in VS Code with nRF Connect SDK:
1. nRF Connect Extension Output In VS Code, go to View → Output. Select nRF Connect...
Hi The Nordic Team,
I am developing a SED device of Matter over Thread. How can I get the ipv6 address of my parent node after my device is connected to the network?
...
This is our first time using TC2050 for the smaller footprint in our prototype. But we can't establish a connection with JTAG in nRG Programmer.
Below is the log from...
SDK: NCS 3.0.2
Part: NRF52840
I am running the NRF52840 as an HCI controller over SPI. I can advertise and connect. However, I need to advertise while connected and support...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
Background
I'm working on a BLE application for the nRF52811 and facing significant flash memory constraints when trying to implement OTA/DFU functionality.
From my understanding...
Hi all,
I'm working on optimizing the power consumption on my nRF52840 DK and need some guidance. Currently measuring ~5µA average idle current via PPK2, but I need to reduce...
Hello
I am trying to perform a firmware update over Bluetooth but without using the external flash on the nRF52840-dk.
At this point I can successfully build the smp_svr...
Hi,
I have custom hardware using the NRF52810. Due to its very small RAM size, I developed the code on the NRF52DK_NRF52832 and then removed functionalities to make it fit...
