Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
I'm stuck trying to set my nRF Connect extension on VSC. I've followed the guide for the installation but I'm reaching a wall. Every time I try to install a given SDK I have...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi everyone,
I'm evaluating the nRF54L15 for a very low-power sensor node application powered by a Lithium Thionyl Chloride (Li-SOCl₂) primary cell. The goal is to achieve...
Device : wearable IOT device
Battery capacity : Max 4.2V (Typ. 3.7V)
BLE Tx Power : Tx power is highest when the battery capacity is 4.2V (measured in air, not conduction...
Hi, We want to use Sensibel microphones in a project with nfr9151, and it will be used to sample one microphone (mono) with 24bit data. This microphone seems to require 32...
Hello, Nordic Support!
I have some problems with programming my custom boards using my nRF54L15dk v0.9.1, when I use a setup with long cables (or several cables & adapters...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi guys,
I'm hitting an error with the current Aliro 1.0.0 lib.
When a credential is signed today but its validFrom is in the future (e.g. signed=2026-06-17, validFrom...
I am doing some development on nRF5340 and I experienced MPU faults. We tracked down the root cause and this led to a PR https://github.com/zephyrproject-rtos/zephyr/pull...
In Zephyr 4.3.0, default swap mode was changed to use OFFSET instead of MOVE. As this is recommended by Zephyr as more efficient method, I wanted to switch to it but ran into...
Hi,
I’m currently trying to get through the SUPL client library license signup process, but my request gets automatically denied every single time.
I have double-checked...
I am attempting to compile some legacy code for the nRF52805, and since adding the flag NRF52805_XXAA compilation fails with the following error:
Which makes sense...
