I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
Hei!
I can't seem to get my devicetree overlay to properly work. I have an external LED and two buttons connected to the GPIO ports mentioned in the overlay, and I've...
Bros, I had updated ncs sdk from v3.1.1 to v3.3.1 today, and when I rebuild an nrf5340 project found that NETAPP ram overflowed, and the error could be represented by build...
Hi,
We have come across AT%XRFTEST command problem for TX test on nRF9151 EVK. We have used nRF9151 modem firmware version 2.0.2 and executed following AT command on nRF9151...
There are two USB ports. IMCU and nrf5340. I had a lot of trouble with bad cables but i found one that works and I find that I have a jlink drive that pops up so I know there...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
Using SDK 2.4.2
1) Is there a way to specify multiple MCUBoot keys in the same way they can be specified for NSIB? MCU Boot allows an array of keys, but it looks like zephyr...
Hi! Do people actually use the 2.2-4.7Ohm series resistor on the VBUS input to the nRF5340? It's just such a low resistance, I don't particularly see the point. Thanks!
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi,
I want to set my BLE advertising as public adress Dynamic, and can't work. I have try reboot,, and call "bt_ctlr_set_public_addr" before "bt_enable", It is working first...
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi All, In the NRF54L15 SoC, the main ARM core and the co-processor RISC core share the same set of peripherals even though both the cores can have separate sections of RAM...
Hello
I need some advice on FOTA via BLE on the nRF54LM20B. I use SDK v 3.3.0, building /ns variant.
I managed to get FOTA working to upload an updated image via BLE,...
