I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
tl;dr: The clone would probably work more reliably if the nrf-toolchain-manager added the --depth 1 option, e.g.: git clone --branch v2.6.1 https://github.com/nrfconnect/sdk...
Dear
I'm working on controlling an I2C device.
I want to achieve TX->TX using the nrfx_twim driver. I specified NRFX_TWIM_XFER_TXTX. When I looked at the nrfx_twim source...
Hello,
During design and schematic entry I used the online datasheet to select GPIO capability. I was advised that I should try out the pin planner to confirm that pin choices...
I am using the nrf_fuel_gauge_idle_set function to handle the fuel gauge state when the system enters a low-power mode. When the charger is connected, I exit this state and...
Hello Nordic Support Team, I am experiencing an issue when using MQTT over an NB-IoT connection with the nRF9151 DK, and I would like to ask for clarification and guidance...
Hi,
I am working on a Matter device based on Nordic NCS v2.9.0, using Google Home as the OTA provider.
I have successfully uploaded a new OTA image in Google Console,...
n the nRF52805, if the hardware is configured for DC/DC regulator operation—namely, with the DCC and DEC4 pins connected through the designated inductor and capacitors—does...
I am using a Thingy91x, with some additional sensors attached via qwiic cable.
Initially to test the Thingy91x I inserted the SIM and scanned the QR code on the Thingy91x...
I am developing a proof-of-concept for remote controlled super-low-power devices using PAwR. I started with nRF52840 (for boths, clients and remote) and now migrated my code...
I built and ran the Matter Light Bulb example for Thread and was able to commission it into Home Assistant with no issues. However, when I tired the Matter Temperature Sensor...
Hi
Setup: nPM1300, nRF54L15-based board, SDK 2.9.2
I am trying to figure out how to use the nPM1300.
So far, I have not succeeded. Quite frequently, after power...
Hi,
I downloaded the NCS v3.2.0, but always got the error below when u npacking the toolchain , the same error when downloading via Vscode. and there is no problem for v3...
Hello all, I am using the nRF52840 together with the nRF7000. To save GPIOs, I would like to use the BUCKEN pin (which is directly connected to the nRF7000) also as the enable...
I tried to compile the project according to the link（ https://github.com/nordicsemi-neuton/nrf-edgeai-thingy53-ble-remotecontrol ）, but the compilation failed.
The compilation...
