I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
While developing my project, I need to receive UDP packets with the NRF9151. My configuration is as follows: - 1nce SIM - VPN between my UDP service and the 1nce network ...
We are using a custom board based on nRF54L15 with MCUboot and compressed image DFU over OTA. DFU was working correctly when updating between NCS v3.2.0 and v3.2.4, but after...
Hi everyone,
I need to implement a coded Phy ble communication in a project and for that I wanted to use an nrf52840 dk. However, for it to be able to compete with the Aircable...
Hello Nordic Team,
I am currently working with the nPM1300 EK together with the nRF54L15 platform and a custom 40 mAh Li-Po battery.
I am facing an issue while configuring...
I'm developing software for the nRF5340 based on the NCS 3.2.4 "hello world" example. Adding bt_enable() returns error code -11. Please tell me how to implement bt_enable...
Hello, I am developing a low-power nRF52840 product using the ncs Zephyr environment. Currently, I have suspended peripherals such as UART and I2C, allowing the system to...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
I've built the softsim external profile from Onomondo and it works. But when I try to incorporate it into the app I'm currently developing, it renders the code unable to boot...
I am trying to enter MCUboot serial recovery mode on an nRF5340 through a UART command.
I mainly followed the Nordic tutorial below:
https://academy.nordicsemi.com/courses...
I'm curious about the approach taken in the nRF Connect SDK's location library for cell neighbor scans ( https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/scan_cellular...
Hello, I am trying to use the latest nrfutil version 8.x.x in my custom project. Previously I had nrfutil version 6.1.7 with `nordicsemi` package included as a dependency...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
I have a nRF9151 dev kit for evaluation that I am following official guide to get up and running using the asset tracker v2 program. I can flash the firmware but I cannot...
