Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Here’s what to check next for toolchain detection issues in VS Code with nRF Connect SDK:
1. nRF Connect Extension Output In VS Code, go to View → Output. Select nRF Connect...
Hi The Nordic Team,
I am developing a SED device of Matter over Thread. How can I get the ipv6 address of my parent node after my device is connected to the network?
...
This is our first time using TC2050 for the smaller footprint in our prototype. But we can't establish a connection with JTAG in nRG Programmer.
Below is the log from...
SDK: NCS 3.0.2
Part: NRF52840
I am running the NRF52840 as an HCI controller over SPI. I can advertise and connect. However, I need to advertise while connected and support...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
Background
I'm working on a BLE application for the nRF52811 and facing significant flash memory constraints when trying to implement OTA/DFU functionality.
From my understanding...
Hi all,
I'm working on optimizing the power consumption on my nRF52840 DK and need some guidance. Currently measuring ~5µA average idle current via PPK2, but I need to reduce...
Hello
I am trying to perform a firmware update over Bluetooth but without using the external flash on the nRF52840-dk.
At this point I can successfully build the smp_svr...
Hi,
I have custom hardware using the NRF52810. Due to its very small RAM size, I developed the code on the NRF52DK_NRF52832 and then removed functionalities to make it fit...
Hi The Nordic team,
After my device reconnects to the gateway from offline again, I don't know what I am doing with this timing every 1s. This situation will not happen...
Hi，
I developed a gateway for converting an MCU to ble Bluetooth. The MCU connects to 8 BLE hosts via UART, and each Bluetooth host can connect to one Bluetooth slave. All...
Hello,
I am trying to configure COMP peripheral on my NRF54L15 DK. I am using P1.11 pin (AIN4) as single ended input for this purpose. For now I am trying only to evaluate...
Hello,
I’m working on a project where I intend to integrate the nRF9151 as a standalone modem , communicating with my external MCU via UART using AT commands .
My goals...
Hi,
Currently I am using nRF52840 as nodes for mesh network. However, by reading the sdk5 documents and example, I did not see any clues to update the firmware with DFU...
