I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I have been following the tutorial for the DECT NR+ Shell (nRF91x1: DECT NR+ Shell). However, I am unable to locate the sample referenced in the documentation:
...
Hello, I try to do work a ism330dhcx on a custom digital board with a custom board in which there is a NRF54L15 microcontroller. The sensor works on other custom board with...
Hi all, I'm currently evaluating a few different vendors, chips and technologies for an idea I've had. It's a wireless+USB gaming HID, so latency is very important. 1kHz polling...
Hello,
We are planning to use the nRF54LM20A, but we do not intend to implement USB in our design.
For the nRF52 series, the datasheet provides a reference schematic for...
Hello all,
Please let me know which module we can use for mesh networking for home automation project (lighting control through smartphone app),maximum how many devices...
Hi, we are currently implementing DECT NR+ mesh network as part of a thesis, where our one part of our plan was to implement full MAC layer (otherwise its just a full mesh...
Hi,
I'm trying to write a generic tool that lists the attribute table of a connected BLE Peripheral. For each discovered attribute I want to log to the console the attribute...
Hello,
I am trying to determine if it is possible to have those 3 stacks coexisting.
I have an iSP4520 chip, which includes an nRF52832 (BLE and Wirepas) and Semtech SX1262...
Hi,
We’re currently integrating the nRF54 series into a product we’re developing, and we’re using the reference schematic and layout as our guide.
While working through...
Zigbee Add-on (R23 1.2.1) doesn't support octect string attribute reporting which seems to be wrong.
I've found this topic that describes the same issue
and a workaround...
Hi Nordic Team,
We are developing a battery-powered cellular IoT device utilizing the nRF9161 SiP combined with the nPM1300 PMIC. Our primary goal regarding power management...
Hi,
We are updating an older platform with the nRF9151 on an add-on PCB.The platform has very limited processing power and buffer space.
The nRF9151 module with the...
I am using the Zephyr NVS Settings module. In some cases this happens: I try to save a value with ` settings_save_one ()`, which internally calls ` nvs_write ()`.
I debugged...
Dear Nordic team,
I have a complex question. In my project I use components which operate at 2.25V as well as they expect 2.25V logic levels.
My idea is to use nrf52840...
