Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello, I'm trying to use the nRF54LM20A, but I'm a bit confused about the reference circuitry. What does "VDD_USB_3V3" refer to? What about all the different antenna labels...
Hello Team,
I am working with nRF52833 configured as a BLE scanner using nRF Connect SDK for VS Code .
Here is my prj.conf:
AND here is scan/conn Implementaion:
...
Affected
zephyr/drivers/regulator/regulator_npm13xx.c (current driver)
zephyr/drivers/regulator/regulator_npm1300.c in older NCS / Zephyr trees
Reproduced on a nRF9151...
I did not get Audio - adc value shows zero all the timse why ??
const codec_register CODEC_DEF_REG_DATA [] = {
// ==========================================...
Summary
With CONFIG_OPENTHREAD_BORDER_ROUTING=y (the default selected by CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y ) and CONFIG_OPENTHREAD_TREL=y (also the default), the...
I'd like to know more about the single-antenna AUX functionality of the nRF9151. More specifically, this line in the documentation for AUX has piqued my interest:
When the...
Hello,
I am attempting to develop an open source nRF52832 PCB design, aiming to minimize the footprint as much as possible.
Thus, I attempted to cramp as many components...
I had one nRF54l15-DK,and I want to make a music player by nRF54l15's BLE,but I am not sure is it supposted LE audio to client my headphone.if it supposted, is it full LE...
I am new to nrf52832 development. The question is that:
I want to do m ultichannel(4 or 5 channels) ADC in scan mode every 1s. and the MCU consumes ultra low current(3-5uA...
As the subject suggests. It is a simple question. I only see development boards with NRF53, but we decided to go with NRF54 in this project. We need BLE and WiFi on the device...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi all,
I am using a tagconnect cable to flash my custom boards using a devkit. I was able to flash 4/5 boards. I first recovered the locked factory boards, and then flashed...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
