GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Enabling CONFIG_USE_SWITCH=y causes usage fault on nRF54L15 with nRF Connect SDK v3.4.0-rc1.
Where it crashes: Context switch on interrupt exit, Zephyr arm-m-switch.c :...
Subject: nRF52833 - OpenOCD ST-LINK MEM-AP Access Failure During Flashing
Hello Nordic Support Team,
I am working with an nRF52833 module and trying to flash firmware...
Dear Support,
I'm using nCS v3.1.1 and the Matter example project. Could you please provide a simple example showing how to use GPIOTE + DPPI + TIMER capture?
My goal...
i am currently working on a board that is using the nrf54l15 chip. and when CONFIG_BT=n or just not included in the prj.conf i see a power consumption of about 80uA on the...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
Hi,
I am using bare metal SDK v1.0.0. On my prototype, I want to use BLE softdevice together with SPIM20 peripheral, physically connected to Port 2. Starting from the BLE...
Hi, The docs, at least for the nrf54L series, cannot be access because the 'site is under maintenance'. The following links don't work: https://docs-be.nordicsemi.com/bundle...
So I have two questions. My first is on the impedance matching network on different pcb stackups. So wouldn't I need a different matching network for a different pcb stackup...
I am testing a custom board prototype and having trouble getting I2C to work.
During testing, I was able to observe activity on the SDA line, although it consisted of only...
Hi,
I am using the heart rate sample.
I have connected ground to ground, 3.3v to vdd, SDA to pin 26 and SCL to pin 27. I have 4.7k pullup resistors on SDA and SCL. When...
Hi Nordic team,
I am opening this new thread as a follow-up to my previous question:
https://devzone.nordicsemi.com/f/nordic-q-a/128246/how-to-reach-datasheet-level-2...
Hello Zephyr Community,
I am trying to contribute a new sensor driver for the **AMS AS7341 Spectral Sensor** to Zephyr (using **NCS v3.2.2 / Zephyr**), and I would appreciate...
