SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hello,
I am developing a project on the nRF54L15 and encountered a system hang when using two UART instances simultaneously: UART20 (for logging and printk ) and UART30...
Hi
I am wondering when I use this function, how much time do I need between I set a TXP and a TXP has been successfully updated. I am developing an application that needs...
I try to set custom compiler flags for the whole project including Zephyr via prj.conf / CONFIG_COMPILER_OPT to compute worst case stack usage as follows: CONFIG_COMPILER_OPT...
Hi all,
I am having difficulties reading microphone data using built-in microphone at Xiao Seeed nRF52840 Sense. I have configured the overlay file as suggested here . Then...
Hello,
I am following the cellular IoT fundamental course with nRF9151-DK.
I didn't have any issue until Lesson 7, but I found that the screen shot of the lesson is...
Hi devzone,
I am starting to write some tests for my application, and I have a couple questions/remarks about the provided Docker image. Link to documentation .
1/ The...
I have done a clean install of the SDK on Debian 13
I have nrfutil install and its working fine - i have tried installing both the v3.2.1 and v3.2.0 toolchains and in both...
Hello Nordic team,
We are using the GRTC on the nRF54L15 , and we are observing the following behavior:
When MCUboot is enabled , the GRTC (likely backed by SYSCOUNTER...
Hi, I am using nrf9151 as a modem running SLM. When SLM comes up, it throws this error. This is a new board run and 50% of the boards show this issue.
I appreciate there...
I am looking for a pairing between Windows laptop or Android mobile on the transmitter side and hearing aid which has bluetooth streaming features as a receiver..
I am looking...
Hi there,
Is it possible to have the DECT NR+ modem trigger events via DPPI? For instance, I'd like to capture a Timer value *exactly* when nrf_modem_dect_phy_time_get...
Hell ,
I am planing to use nRF52810 for one of my mesh application,now query is
How much power consumption its will take when RF is disable and listening only external...
Hi
We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below
The PDM DATA high level will decrease periodically
Is this waveform normal? If yes...
Hi,
I know that pc-ble-driver-py is archived but as there is no real alternative to it, I'm still using this package...
I'm using BLE nRF52840 dongle to connect to...
I am using the nrf52833 with 17.1 SDK and s140_nrf52_7.2.0_softdevice，i want to scan a scannable extend adv packets，
This is what i get in the BLE_GAP_EVT_ADV_REPORT ： ...
