I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello Nordic Forum,
I ran the Power Profiler Kit on an nRF52DK development board to establish a baseline power consumption.
The current firmware project is quite simple...
Hi,
I am developing a low power BLE device using Promicro nRF52840 boards. After updating to ncs3.2.1 I have noticed a high power consumption in sleep, that isn't present...
Hi! I'm running into a strange issue.
I have inherited this project and it is poorly commented. I have 2 peripherals and 1 central. The 2 peripherals are identical devices...
I am developing a product which uses one nRF5340 Timer in timer mode and another in Counter mode. Reading through the nRF5340 Product Specification v1.6 I have the following...
Hello Support Team,
I am currently working on Channel Sounding with the nRF54L15 devkit, and I am encountering an issue when using main_mode .
Until now, I was using the...
After defining the ADAPTER and initializing UART2 the The adapter pointer fails a test on line 287. FATAL: async_adapter_uart2 points to Flash (0x246d4). Linker Error. This...
Hi, I've tried signing up for a SUPL licence a couple of times but it keeps getting denied. Not sure why. I have logged into devzone.nordicsemi.com and am using the same email...
I’m trying to read/write data to the internal flash of my nRF54L15 SoC using the NVS (Non-Volatile Storage) library.
I successfully flashed the sample nvs application on...
I try to write data into the OTP section of the APP core with the following command line:
nrfjprog.exe -f nrf53 --program 'OTP.ihex'
ouput:
[error] [SeggerBackend] ...
I am trying to program MS12SF1 module through nrf5340DK. I tested the blinky code to toggle the LED pins but while checking through oscilloscope the pins showed nothing, wasn...
nRF54l10 on our custom board in system off has high current consumption, approx 98 uA.
Utilizing the system_off code (C:\ncs\v3.0.2\zephyr\samples\boards\nordic\system_off...
I have got to start with nRF7002-dk and the Wi-Fi sample from the quick start is not working.
I have tried to compile the code on VS code and flash the same code on the...
I would like to estimate the current consumption when the controller is advertising at 2.3Seconds, using external crystal, Tx power of 8dBm, Tx payload of 31 bytes. When I...
We are facing in BLE connection issue in Android phone.
we are planning to use 1. Android phone with 'nRF Connect' for mobile as BLE central. 2. Long range demo applictaion...
Hello.
I am currently testing nRF Cloud and encountering an issue.
I have flashed the Peripheral Memfault Diagnostic Service (MDS) sample program to an nRF54L15DK and...
