At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Back in SDK 17 or so there were code samples for both the client and server side of the LED button service.
What happened to the client/central example when you migrated...
Description
I'm working on a battery-powered application where WiFi needs to be shut down between cloud sync intervals. I'm following the same pattern as the wifi/shutdown...
Hi,
working with nRF52840 with S140 v7.2.0, not sure about SDK version. VS Code + ARM GCC + LD Gold linker.
I changed stack and heap sizes via __HEAP_SIZE and __STACK_SIZE...
We are experiencing an issue with high current consumption when using the nPM1300 powered by a battery. In Hysteretic mode, the battery current draw measures 109 µA. However...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
I'm trying to put my code on a RAM/ROM diet and cut out any extra cruft so it will fit in an nRF52832. It used to fit with older SDKs, but not with the newest (v3.2.3).
...
Hello,
I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware.
The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
Hello, I have a particularly weird problem that I can't figure out how to solve. I was using the 52833 DK for software development and the onboard leds were blinking perfectly...
Hi.
I'm fighting to get an i2c scanner (re)expose external devices' hex addresses on an Xiao nrf52840 board under VsCode nrfConnect (the basic board, not the Sense version...
Hi,
we are designing a custom board based on the nRF54L15 QFAA (QFN48) using a chip antenna with coplanar waveguide feed on a 4-layer PCB.
In the Nordic reference design...
Hello, We're improving a battery-powered (CR2032) sensor tag based on an NRF52833 with a 868 MHz transceiver. We want to use the nPM2100 PMIC and would like to optimize the...
Dear Nordic Team,
We are seeking assistance in resolving a significant power consumption gap observed in our nRF9151-based asset tracker. While our lab testing suggests...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi,
I am working on a custom board based on the nRF5340 using Zephyr RTOS with external QSPI NOR flash.
I am facing an intermittent issue with the external flash.
Observed...
