At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Summary
With CONFIG_OPENTHREAD_BORDER_ROUTING=y (the default selected by CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y ) and CONFIG_OPENTHREAD_TREL=y (also the default), the...
I'd like to know more about the single-antenna AUX functionality of the nRF9151. More specifically, this line in the documentation for AUX has piqued my interest:
When the...
Hello,
I am attempting to develop an open source nRF52832 PCB design, aiming to minimize the footprint as much as possible.
Thus, I attempted to cramp as many components...
I had one nRF54l15-DK,and I want to make a music player by nRF54l15's BLE,but I am not sure is it supposted LE audio to client my headphone.if it supposted, is it full LE...
I am new to nrf52832 development. The question is that:
I want to do m ultichannel(4 or 5 channels) ADC in scan mode every 1s. and the MCU consumes ultra low current(3-5uA...
As the subject suggests. It is a simple question. I only see development boards with NRF53, but we decided to go with NRF54 in this project. We need BLE and WiFi on the device...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi all,
I am using a tagconnect cable to flash my custom boards using a devkit. I was able to flash 4/5 boards. I first recovered the locked factory boards, and then flashed...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
Hello,
I am working with the nRF9151 DK and NCS v3.3.0 . I am experiencing a critical modem fault at startup.
Problem Summary: When I start debugging, I immediately get...
I attempted to conduct Bluetooth development using the nRF52840DK (NCS 3.2.0), but I encountered an MPSL error:
ASSERTION FAIL [0] @ WEST_TOPDIR/nrf/subsys/mpsl/init/mpsl_init...
Hello,
I am trying to add different ConcentrationMeasurement cluster types to my application (CarbonDioxide, VOC, Pm1, etc.) but have an issue with zap-gui not saving the...
Good day,
I have been making use of the nRF54LM20A SoC with ncs v3.2.0. I am currently trying to use the high-speed SPI (SPIM00) lines on Port 2 to communicate with an SD...
