Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Dear nordic support team,
Hi! Wish you have a good day.
I am currently using the nRF54LM20 DK, which has the nRF54LM20B MCU. I would like to use the EXP pins to connect...
Hello,
I'm running nRF Connect SDK v1.9.0 on two nRF52840-DK devices, one Peripheral other Central.
My application requires to initiate pairing, i.e. send pair request...
Dear Nordic team,
we are evaluating the nRF9151 for a data acquisition application/device. Our first goal was to get the official HTTPS client sample to run on the nRF9151DK...
Hi Nordic team,
I am working on a custom board based on the nRF54L15 using nRF Connect SDK v3.1.0.
On our hardware, the nRF54L15 has a 32 MHz crystal connected to XC1...
Hi Folks & experts
I hope you ALL are well.
I wanted to share a bring-up result from my XIAO nRF54LM20A workbench and ask for your guidance.
I have the XIAO nRF54LM20A...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hi
I'm encountering a problem than the ANT device cannot be scanned. you can use project "ble_ant_app_hrm_v324"(ncs 324）, and modify "
light_rx_open_head" to connect...
Hi Asbjørn，
As I mentioned in case 352770
We are in same question as the initial question issued by our colleague RongLinQin. As I mentioned, we want to conduct BLE OTA...
Hello.
We are developing a project based on the nRF54L15 SoC, utilizing MCUboot, image compression, and TF-M (Trusted Firmware-M). As part of our upgrade from NCS v3.2.4...
Hi!
I am using nRF9151-DK, enabling UART1 and using CONFIG_UART_ASYNC_API.
The build is successful, but the problem every time i connect a flashed kit with this binaries...
I'm trying to get NFC power-up/restart working on nrf54lDK but the call to sys_poweroff() results in: E: ***** BUS FAULT ***** E: Precise data bus error E: BFAR Address: 0x0...
Hi, We are using nRF Connect SDK v3.0.2 (Matter 1.4.1) We are trying to do Matter certification, but we have an issue on TC-RR-1.1 and TC-OPCREDS- 3.1 The device crashes randomly...
We are building a line of product to be used in big size building light management and control.
We believe that both the IV values and a huge quantity of SEQ separate counters...
Hi everyone,
I'm developing a star-topology network using DECT NR+ on nRF9161 DK nodes, running modem firmware mfw-nr+_nrf91x1_2.0.0 (nRF Connect SDK 3.3.0).
My issue...
