I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hello Team,
I have added the LittleFS file system for the external flash and am able to program the .bin files through code by keeping the bitmap array within the application...
Hi All,
I would like to know if the reset can configured to trigger by "failling edge" rather than "rsing edge" of the reset pin / configured pin?
Per the datasheet from...
While debugging the NCS 54L15 ESB module, I observed some anomalies when measuring the radio interrupt signal. For example, after the RADIO READY event is generated, it should...
Hello,
We are working with the nPM1304-QEAA-R7 in a power management application and would like guidance on how to implement or connect a fuel gauge to this device. Specifically...
Hi I could not program the device via OpenOCD (current release) The programm tells me "invalid subcommand "write_image erase prog.hex" I modifed the nrf54L.cfg
added "flash...
I have a Power Profiler Kit II and have been using it for a few years without issue. I have been using it through the nrf Connect for Desktop software and the Power Profiler...
On the nRF54L15, is it possible to configure MCUboot so that the secondary image slot is stored in external flash connected via the SQSPI interface instead of internal flash...
Hi,
We're looking to integrate the NPM1304 in a product with a very small battery. As per the NPM datasheet we've selected a battery with a PCM.
We've previously seen...
We have a production system based on asset_tracker_v2 in V1.7.0 and V2.5.0. it normally connects and publishes fine 24/7. we have many sensors in the field. There are time...
Hello Nordic team,
I have a retail Thingy:91X device. IMEI: nrf-359404230239544
It connects to hello.nrfcloud.com, but I cannot add it to my own nRF Cloud account because...
We currently have a self-developed development board with NRF5340. The example program uses Bluetooth transparent transmission. Now I have added a GPIO pin: en_power is set...
When I was running the dm process of Connect SDK 3.0.2. I wanted to make one device as the initiator and six devices as the reflectors. I expect that the reflectors will not...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hi,
We have developed a custom board with both nRF52833 as the BLE beacon and nRF7001 as WiFi. We have chose to use patch antenna with UFL connector for both. When we tried...
