Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
I am a developer/maintainer for the RF24 Arduino library at https://github.com/nRF24/RF24
I've found in some cases, the R_RX_PL_WID register returns 0 while the...
When updating from nRF connect SDK v3.0.1 to v3.1.0 we noticed a change in the clock_gettime() function.
In the old version, the clock was not reset by a reboot.
The new...
nRF5340 I2S MCLK issue – unable to get 12.288 MHz MCLK for 48 kHz sampling
I am using the nRF5340 SoC and configuring the I2S peripheral as Master to achieve a 48 kHz audio...
Hi,
I get a PCBA which contains the following test points of nRF54L15 : P0.02, P0.03, P2.07, P2.08. I would like to set one of them to be UART TXD.
In pin assignment...
hi support team,
customer is using mesh and met a problem, here is the situation:
1. customer using mesh/light as basic demo, adding mesh DFU function in it ,and deploy...
*** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr OS v4.1.99-ff8f0c579eeb ***
Hi,
I purchased several nrf54L15 development boards and am preparing to...
I'm trying to run a custom image on the net core. I've successfully done so using the following exercise in the intermediate course: lesson 8 exercise 2 however when trying...
Hello,
We have some hardware that uses the nPM2100 in roughly the 'one button' configuration where the SHPHLD signal is used for the reset button as well. When the reset...
Hi, We have a device already in production. We have an issue where the device fails to connect to an Android phone or iPhone hotspot with WPA3-Personal. We tried to change...
nRF54L15 - NCS 3.02 - Toolchain 3.02
I'm exploring using the Zephyr Shell to replace my old legacy CLI interpreter which hooks onto a uart callback. I can set up custom...
I get the error "ImportError: Module use of python312.dll conflicts with this version of Python." when I try to flash my device using any Python version below 3.12.x. I get...
Hi,
I have a project with nRF52840 where I uses 3xSPIM. 2 are connected to a real-time-clock and accelerometer. The third is connected to an SD-card.
I realized that the...
Our project requires a more efficient way to collect live trace Diagnistic trace data from LTE-M RRC and NAS, on a Thingy:91.
However, using the " Cellular Monitor " app...
Bit baffled by this one, I assume it's related to the attempted nRF SDK Intellisense magic: We do have a monorepo for various controller projects that includes two zephyr...
