Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Problem:
Reset reason logic works correctly when programming via SWD
After DFU programming, reset reasons are detected incorrectly
Even after unplugging/reconnecting...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
Hi
I'm using the periodic_adv_conn example from SDK 3.0.0. In the request_cb function, the bt_le_per_adv_set_subevent_data function is used to load data for future subevents...
Hi,
I want to use the die temperature sensor in the nRF54L chipset and am wondering why the definition have changed slightly compared to previous chipsets. In the SoC device...
How precise do the trace antenna dimensions have to be? Given that the datasheet for the nRF54L15 only has a reference layout up to and including the matching network, but...
Hi Nordic:
We currently need to provide the RoHS and MSDS test certificates for our product's NRF52820QDAA-R. I checked the certificates on Nordic's official website, but...
While testing, I encountered the following error after flashing the modem firmware and running the DECT example:
<err> nrf_modem: Modem has crashed, reason 0xfff, PC: 0x0...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
I am new to this device, so please bear with me during the inevitable simple misunderstandings! I am scanning for bluetooth devices and getting sensible numbers of devices...
Hi, I have a custom board with an ISP1807 onboard. We'd like to optimize the production process, especially the programming process. We currently use the nrf52840 dk board...
I have a small demo, based on the hello world example, where I have also enabled gpio_keys. I can run this on the nRF52-DK, nRF54-DK but when I come to run it on my custom...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
