Problem Description
The custom hardware board cannot boot normally after flashing the firmware. However, the exact same firmware image works perfectly on the official nRF54L15...
Hello, I am raising this issue because I am working with multiple devices doing CS procedures between each other and I found a limitation. I am working with NCS 3.3.1. When...
For my project I want MCUboot with the upgrade image placed in the external flash, and TF-M. I am not able to get this combo to boot however, and I suspect the reason is that...
Hi!
I am trying to do a DFU with external flash, using a nRF54L15-DK development kit.
To evaluate this feature, I use the l9_e3_sol example available on GitHub (I use...
I am beginning to work on a next generation of environmental sensors. The current group of sensors use the i2c, or oneWire communications bus. The current standard micro-controller...
Hi, I'm experiencing flash write issues on an nRF54H20 DK's on-board NOR flash. I'm using ncs and toolchain v3.3.0.
Setup: the on-board MX25UW6345G on EXMIF, using the jedec...
The goal is to have the nRF52833 stay in sync with GNSS time without the external pulse per second for some significant time (some minutes). This is not possible with a normal...
Hello,
I used nrf52832 as a scanner.
Now i use it to scan only one tag. And the TAG advertise data addcoring to ble 4.0.
Now i find scan channels are not 37,38,39,37...
■Development environment nfr52832 SDK_12.3.0
■Question I'm making Central's module. After connecting with a peripheral of pairing finish, the function(pm_peer_rank_highest...
Hi all,
I am trying to test OpenThread protocol for an application that we have and we want to use the CLI interface as the application logic should stay in the application...
Hi all,
I was in the process of buying 3 nrf52-dk boards. I need to know if one can differentiate all of the different boards on their PC when connected at the same time...
Dear Nordic Team,
Thanks for support
Currently i am work with VL53L0X in ble_uart_app example. it working fine , but its take 5ma current. How can i use TWI in low power...
Hi,
I would like to know if you can sniff BLE packets with really low transmission power, for example can you sniff a -35 db signal with any average bluetooth receiver?...
I've used PCA10040 sdk15.0 example ble_peripheral ble_app_uart
I can handle it through terminal.
If I insert strings through terminal, App can receive.
But, I...
hii,
i am trying to interface the nrf24LU1+ and nrf52832. I wanted to know if i can program the nrf24lu1+ without the requirement of nrfgo motherboard. or is it necessary...
I don't want to use MESH， because there are too many data
Application scenario
Mobile phone ------------> DeviceA --------------------------------------> DeviceB
...
Hello,
Would there be any particularly adverse side-effect if two NRF51822 GPIO pins (e.g., P0.18 and P0.19) were shorted together? One of the pins (e.g., P0.18) would be...
SDK ：15.0.0
Examples：ble_peripheral / ble_app_uart / pca10056 / s140
Board：nRF52840 DK
After pairing, may be connected, because the indicator lights continue to shine...
Hi,
I am using sd_ble_gatts_characteristic_add to set a characteristic in my service. The function call return 0 - NRF_SUCCESS but when I browse the service with nRF connect...
Hello,
I try to add pairing functionality to my app. Error code NRF_ERROR_INVALID_PARAM occur from the sd_ble_gap_sec_params_reply when i want to read my characteritic...
Hey, I have a sensor (ADC with data rate is 250 sps), attached to nrf51822. It has Data ready pin (output), which toggles from high to low when data is ready. Also this sensor...
