Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hello - I have the exact same question as proposed in this thread - I am wondering if there has been any change in the 3 last years since it was posted.
In a nutshell, we...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hello,
I've written a shell cmd on the 9160DK to send an sms. it handles getting the data in the correct has the following format,
sms <len> <pdu data>
I've used the...
hello,
I am trying to integrating ble_nus_init( ), inside ble_beacon_app, receiving through NUS_service and transmitting through beacon,
but program is stuck inside ble_advertising...
Is it possible to assign connection handles non-sequentially, for example based on the device's Bluetooth name? For the solution I'm developing I'd like for a given sensor...
Hi,
I am getting lots of transmission errors using the Serial library. I changed the Serial_Uartes example by removing the serial1 interface and creating a simple loopback...
Hi all,
I am using nRF52832 DK to do some tests about power consumption. And I am facing a problem that every time I pressed the button and kept it down, the current would...
Checked out v1.0.0
This error seems to be unavoidable to me. I have deleted the git cache and even tried the --no-cache-dir option to pip3, but nothing seems to work.
...
Is there any documentation available explaining how to access the LTE modem without using the SDK ? Kinda limited information regarding the IPC peripheral and how to use it...
Hi,
We are developing a bluetooth scanner with our custom application on nrf52840 based custom board. We have external oscillator on our board. When I try to call the sd_softdevice_enable...
Hi All,
I am trying to build ANT examples for nrf52832 and i am getting below error.
PATH : nRF5_SDK_16.0.0_98a08e2\examples\ant\ant_advanced_burst\pca10040\s212\ses...
Hello,
The datasheet shows example circuit configurations with C3=C4=1pF and L1=3.9nH. But the downloaded reference design shows C3=0.8pF, C4=0.5pF, L1=4.7nH, plus an empty...
I try to incorporate the usb dfu trigger into my application. However when using nrf Connect for Desktop to flash the nrf52840 dongle it can not reopen the dongle.
This...
I'm using SDK 15.3 and Mesh 3.20 on a system, that works fine with LPN and nodes with friend-features. The LPN can initiates (establish) friend connection, request status...
Hi !
In order to consume lowest current，we use the function power_manage() ，let the MCU go into sleep，the SD is S130, V1.0，we enable the GPIOTE，watchdog ，ADC ，app_timer...
Hai, I'm trying to learn the UART using the example code available in nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart. I'm using BMD-300 Evaluation Board. I'm...
