Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I am looking for (andriod) mobile phone that support Bluetooth LE coded (long range)
Have you ever tested bluetooth (LE coded) with mobile phone ?
Please recommend...
I am currently developing firmware that needs to run on both 32 and 40 chips.
The basics of the situation is the firmware contains 3 'applications'. A flag in the UICR region...
Hello,
I have been looking through the SDK for the Thingy:52, and I have been unable to find the configuration file used for the MPU-9250. I am able to see the default pedometer...
I use QSPI to access MT25qu512 serial flash and find the following behavior.
SDK: nRF5_SDK_15.3.0_59ac345
QSPI configuration:
// Use 4 bytes address from serial flash...
I am unable to figure out what causes the problem that IRQ handler is defined both in nrfx_uart and nrfx_uarte modules.
After investigating in a test project I have found...
I have previously built the Asset Tracker downloaded it to my 9160DK with no problems.
Today I connected my Thingy91 and updated it's firmware. Afterwards I built the Asset...
Hello,
I'm trying to create a Mesh network with the following devices:
* Mobile phone as provisioner (supports PB-GATT only)
* Two different bulb's which supports PB...
When storing entries that aren't multiple of 4 bytes they are padded with random bytes by flash manager.
The problem is that they aren't padded with 1's but rather random...
I'm testing with a Custom board using a nrf52832 chip.
Testing BLE communication using nRF Tool Box.
I am using SDK15.3.0 example for communication using nRF Toolbox and...
Hi,
I am trying to install the nrf command line tools on linux. After following the installation instruction, I have the error
ERROR: nrfjprog.ini not found. Please reinstall...
Received the IN-119 notice, and it says:
All users are recommended to use the latest release of BLE protocol stack software for product development. All BLE protocol stacks...
Hi,
Using SDK 15.2.0 and SD S140_6_1_1.
I have two hardware of nRF52840, one has external LF crystal(32kHz) and another does not.
Want to run same firmware file in...
Hi i have questions about nrf52832 and nrf52811 soc.
Currently we are selling custom board with nrf52832 soc which works fine and going out for sale
In the custom...
