I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Is there an example of using sd_ble_gattc_write() to do a long write?
I'm assuming I need to use BLE_GATT_OP_PREP_WRITE_REQ and
BLE_GATT_OP_EXEC_WRITE_REQ.
devzone...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
I see there have been some issues with TWI in early revs of silicon, but looking at SDK 6 I see the twi_master_hw uses the silicon hardware to read/write the I2C device, but...
Hi
Can I use Bluetooth software version 7.1 en SDK versie 6.0 with the nRF51xx C0 Nordic version?
Or do we need the G0 for that?
and what are the main differences?
...
Hello
Where can I find operating characteristics of pstorage_store and pstorage_update?
Actually, I observe that about 100 ms are needed to update 4 bytes data. For...
Hi All,
I have two application modules which will use the flash , 1) Bond manager 2) configuration file
I have register both modules with different parameter in the initialization...
keil 5.12 could install pack file. I'd like to install S130 0.9 to keil 5.12, but I did not find S130 0.9 pack file. Could I install S130 0.9 manually and could select the...
Hi....
we are having some issues while testing our profiles in ios app.when switch from application to dfu am calling "sd_ble_gatts_service_changed(m_conn_handle,0x01,0x4D...
I'm looking for a simple and inexpensive solution for tying the TX and RX pins to GND after burning the OTP in production. What have other people done? I'd like to avoid having...
We are trying out nRF51822. My colleague has a top of the line Lenovo running Ubuntu and is able to detect the module when scanned. However, my macbook pro Mid 2014 (Which...
Hi everyOne , i have been trying to upload my hex file into my controller, but every time i click the "Load" option in KeiluVision a window pops out..! it shows " No Cortex...
One question came to mind while browsing through the SDK example code documentation:
as there is a blinky and a blinky RTX example, do all the projects which use the soft...
