I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hello,
I would like to sample the battery level of my nrf52832 DK and send it through BLE. I have started from the example ble_app_hrs for SDK12.2 since the service was...
Hi,
Most of the sections of my application are functioning as I want it to, except these two (step 3 and step 4).
Application:
Connect device (with Auto connect...
I noticed while running a Bluetooth scanner app on my iPad, while testing one of my devices, that it was showing someone else's device in the locality.
What I found strange...
Hello!
I have:
nRF52840-Preview-DK (pca10056)
nRF5_SDK_13.0.0_04a0bfd (s140)
I load **nRF5_SDK_13.0.0_04a0bfd\examples\ble_central\ble_app_uart_c\hex\ble_app_uart_c_pca10056_s140...
I have an interrupt coming in every 50-150 microsecs and I want to measure these intervals as precisely as possible.
I tried this with SDK12.2:
APP_TIMER_INIT(0, 5,...
We're trying to bit-bang SWD to program an nRF52832, and we're running into some problems getting the nRF52 to respond. One theory is we're not generating a high enough clock...
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
Hello,
I've noticed the following sentence in s132_nrf52_3.x.x release notes:
"Synthesized low frequency clock source is not tested or intended for use with the BLE...
I'm following the tutorial in the NRF52840 SDK on setting up a Thread Border Router here and I've run into some issues during testing. For one, I'm trying to resolve ipv4...
Hi,
I'm able to successfully enable Access Port protection, either using nrfjprog or by setting NRF_UICR->APPROTECT register to 0xFFFFFF00 in code.
But I have a problem...
Hello,
Since this seems to be a very hard topic to find info about (its very contradictory and confuse) I'd like to ask a Nordic employee directly.
I'm planning to build...
This concept keeps popping up when I'm dealing with mesh networking.
My guess is that, to avoid air collision, packets/pdus are sent on a randomized or predefined combination...
Hi,
I am using ble_app_uart for my development, in that I have buffer size of 2kB which will store all the incoming data and the data will be processed and send over NUS...
