Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Can you please help to suggest how to get hci logs in channel sounding examples? Like my use case is that I want to know which commands are going from host to controller and...
Hi all,
I'm working with the nRF52805 (QFN16) and was curious if the nRESET pin (P0.21) can be disabled via the UICR->PSELRESET[n] mechanism, as is possible on other nRF52...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello,
I am trying to build a firmware for the nRF5340 on the Thingy91:x. The firmware should use the external flash for the secondary Image and is using the chained bootload...
I've been working on a custom device utilising the nRF52832 that needs to switch GPIOs in tightly controlled pulses. The problematic section is part of a much larger project...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
Hi, on nRF54L15 Dev Kit, we are trying to validate our sleep current consumption. We are seeing sleep current of ~100-300uA, when it should be a fraction of that. As per datasheet...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi support team,
We are using nRF9151 with NCS v2.7.0 for our IoT product. During power optimization, we observed:
Even after disabling UART RX interrupt using uart_irq_rx_disable...
Hi there, I am trying to find the logic implemented in a source code which performs the following steps: 1) reading from a binary file that represents the firmware image that...
Working on the nRF52833DK board and based off the nrfx_spim_spis advanced non-blocking example sample. I've already converted the SPI master to use the Zephyr driver instead...
We want to use PSA crypto to generate a persistent key that can't be read out and use this for encryption/decryption.
We have of course tried the persistent_key_usage sample...
Hi all :
I am trying to use the nRF54L15 built-in load capacitor for crystal but I do not know how to measure the crystal performance, such as driving level and negative...