I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi Everyone
I have added all the required paths for the ble_app_uart example but the program can not find the files like ble_advertising.h and nrf_sdh.h files which are...
hi support
Thinking of attendance system using bluetooth Identity cards
what is maximum nos of cards can a nrf52 scan at a time.
suppose there are 100people in a room...
I have just received my development kit and following the getting started instructions on website. But I am stuck at point 7 of this link https://www.nordicsemi.com/eng/Products...
hello Nordic team
I am using nrf52DK.how to use spi to read /write data .I have seen sdk14.2.0 in folder nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi.
I am trying to interface an atmega32 with an nRF24L01. I am trying to communicate between two nRF's. But before proceeding to that, I set out to test the SPI connection between...
I put the nrf_ble_ancs_c_request_attrs in the BLE_ANCS_C_EVT_NOTIF event(added). But only return back 1 or 2 BLE_ANCS_C_EVT_NOTIF_ATTRIBUTE event. I am using 12.3.0 SDK example...
Hello,
This in reference to Case ID: 121570.
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery from Panasonic. We have calculated...
i am using my custom board with nrf51822 and using sdk 12.3.0 .
the led blink example works fine on it but when i upload ble_app_uart then bluetooth is not advertising.
Hi i just get nRF52832 PCA10400 DK.
I am using SDK14.0.0. i tried to use /example/peripheral/spi.
i don't set the gpio set and high or low.in the SDK14.0.0, how to set...
Hi!
I'm using a barebones example project from SDK 12.3.0, under examples/peripheral/uart, with two versions of nRF52-DK boards (pca10056 and pca10040). The goal is to read...
Hi,
I am looking for the carrier tape spec for nRF52810-CAAA.
I am referring to the following document but nRF52810 is not listed.
nWP024 - Embossed Tape and Reel...
Hi,
I'm using a NRF52832 development kit and SDK v14.1. My application is simulating several bluetooth devices for testing purposes. The device I'm simulating doesn't support...
Dear All. I have question about compiler of nRF5_SDK_V12.3. I compile the example BLE_peripheral\experimental_ble_app_blinky by gnu arm(latest version). It can work on nRF51...
Hi,
I am having problems with a custom board using pin 0.10 as GPIO.
I have added -DCONFIG_NFCT_PINS_AS_GPIOS to my makefile. Without that, as expected, I am unable to...
