Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Dear Nordic-support,
I am trying to use the modem_battery_low_level_handler and modem_battery_low_level_set(), but I think there are two different ranges for the battery...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
Hello,
I am studying the materials in Bluetooth Low Energy Fundamentals.
I cloned the codes from GitHub https://github.com/NordicDeveloperAcademy/bt-fund
I tried to...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
The BCLK_CONT option to i2s_configure() is not being honored anywhere. How do I get BCLK to output continuously without having to do i2s_write() or i2s_read() calls over and...
Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
Hello, I am trying to use the DPS368XTSA1 sensor with the nRF52833 via SPI. First, I’m attempting to read the sensor’s ID during initialization, but it’s not being read properly...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hello everyone,
I'm using the ble_app_uart example code in my MDBT50Q-U512k. I have been made some modifications according to my application. I need use fixed value pin...
