Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
Dear Devzone Community,
when trying to get the Zephyr SHT31 Sample running, I stumbled across an error which I was not able to resolve.
I did the following:
Add nrf9160dk_nrf9160ns...
I need to control the BLE ON/OFF state and send some data to MK81 via BLE through UART, we have estalished the Hardware connection between the nRF52832 chip and MK81,
How...
So, I am quite beginer with programming and working with this sensors and nrf, So I need your guys help.
I am trying to get the x,y,z values from the accelerometer of BMX055...
The nRF 52840 RSSI "meter" is not usable.
I tested in an RF (2.4Ghz) quiet neighborhood. Using a reference receiver, I measured RSSI variance around +/-3 dB (95% confidence...
Hi
Q1. Can SES Nordic fork generate unique checksum for code verification? It's like what Microchips compiler did.
Microchips compiler can generate checksum after code...
Hi there!
Okay, we're back again... I'm using ARMGCC in combination with Make, nRF5 SDK, nRF SDK for Mesh, FreeRTOS and C++. This time I wanted to use the APP_BUTTON library...
Hi Nordic,
I am a beginner in programming outside of the Arduino IDE. I'm familiar enough with C to understand much of the code in the examples, but using I2C with the...
Hi. I am currently using an nRF52840 DK board and SDK 17.0.2.
My team is implementing a default key for the first connection to device.
During the connection, we plan...
Hello, I am currently trying to build the lwm2m_client sample on my nrf9160DK but I am facing these issues in my Kconfig file, specifically with the BSD_LIBRARY dependency...
Hi,
I noticed (as highlighted in screenshot below) some of the IP based BLE projects under “Experimental: IoT Examples” found in all previous versions of nRF5 SDK that I...
Hi
We've recently added FreeRTOS to the firmware of an existing product (primarily to pre-empt big chunks of 3rd-party code over which we have no control and execute them...
Hi,
As discussed, the instructed PCB land pattern for nRF9160 is according to Product Specification:
However, we have noticed that land pattern exceeds nRF9160 dimensions...
Hello ,
I am trying DFU over BLE.I am using SDK 14.0.2 .
i Flashed Bootloader Code and Softdevice 5.0.0 .then Device is Starting Advertised as DfuTarg and As Mention in...
Hello,
i have one nrf52840 board with a coded phy scanner and another sending advertisings, when it are close , i received in the scanner 100% of Advertisings, but when...
