i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi community ! Here : https://devzone.nordicsemi.com/f/nordic-q-a/62414/different-behaviour-with-same-program-and-boards i get some problem with different behaviour when programming...
I'm using the Laird Connectivity BL654-DVK board as a basis for evaluating the nRF52840 for our application.
I started by using the .../examples/ble_peripheral/ble_app_hrs_freertos...
Hi,
When we do the UART stress testing with serial_lte_modem sample, the slm will crash by sending AT commands with interval 100ms.
the debug log will show "<wrn> at_host...
Hi ,
I have question about the specification of CPU running current. We did measure the current by PPK to force the CPU always running but the result is quite different...
Dear DevZone, I'm trying to perform a BLE OTA DFU with two nRF52840 Dev Kits. I followed the step by step guide from Nordic provided at the following link: devzone.nordicsemi...
Hi , Dear Nordic supports:
I am using NRF52832 for the iterative development of a product. In the previous generation of products, I used a PWM control LED flashing, whose...
Hello.
Could someone recommend me a verified antenna RF Switch for AoA using Bluetooth nrf52811 ?
What parameters are crucial for proper functionality with nrf52811? ...
Hi,
In ble_app_cts_c example(SDK 16), is it necessary to perform app_timer_init()? Because I could see that, no timers are being setup in the function timers_init().
If...
Hi,
When I read about interframe spacing in the product spec ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fradio.html&cp=4_0_0_5_19_8&anchor=ifs ...
I have a nrf52832 chip acting as a serial passthrough to an external app. Basically, it works great, unless I start sending high amounts of data into it. Once I do that, I...
I am developing an IoT system in which I need to link multiple devices to a master, which is why my nRF52810 chip caught my attention so I am interested in knowing how many...
The address range for Bootloader is from 0x0007 8000 - 0x0007 E000 for SDK 16 on nRF52832 device. See this link ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16...
Dear Sir,
Using SDK 16.0 for NRF52833. My application uses NRF FDS lib (flash data storage)
Immediate fds read after fds write gives 0. But after a board reset I get...
Hi,
I am using nRF52840 S140 with ble_app_blinky application. I have a basic query of GPIO configuration when moving from Bootloader to Application.
We are using Secure...
