Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
According to this thread, iPhone 11 Pro supports Long Range (Coded PHY) : https://devzone.nordicsemi.com/f/nordic-q-a/33060/is-there-any-smartphone-with-supporting-of-bluetooth...
Hello,
I am upgrading to SDK 17.0 from 15.0.
When I try to to compile my project i get this error:
../_Release/Release_Commercial_Debug/Main/Exe/Main.elf section ...
Hi,
I followed the tutorial in the Github and create a custom service. (Github: https://github.com/NordicPlayground/nRF52-Bluetooth-Course )
1. I use the ble_cus_custom_value_update...
I have an issue with my Thingy:91
1) I unboxed
2) I successfully connected to my Windows machine and updated the modem firmware
3) Turned off power
4) Turned on power...
I would like to add a simple ble BAS (battery service) to appear along side my custom services... but for the life of me I cannot find any information, or tutorial on how...
I build project without problems, but this simple sample return zero results for read buffer. I return 5 zero from 5 zeros. I have right names for overlays files. nrf9160_pca10090ns...
I'd previously run into this problem with mqtt_publish not being able to handle large payloads, larger than approximately 2k.
At the time, the suggested workaround was to...
Hi All,
I am working on a project where i need to communicate using i2c protocol. For this i need to set i2c frequency 20 Khz. So how can i calculate register value to set...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
Hello,
Considering the waveforms in the following chart, which will be the best approach to keep the power consumption as low as possible?
Specifically, which peripheral...
Best regards:
I have one PTX and one PRX, both nRF24L01+ with PA and LNA. PTX send 4 bytes to PRX but PRX doesn't get RX_DR, and PTX fire MAX_RT.
PRX:
PTX:
...
Hi
I had a strange error when I Set up a project in Segger, I got TRUSTED EXECUTION NONSECURE error.
I was trying to build the project for thingy:91 with nrf Connect SDK...
