NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello DevZone,
SDK 15.0.0 SD S140
Currently working without an active SoftDevice but even with an active SoftDevice these problems keep occurring.
I'm currently working...
Hello! I need help implementing a TDMA on a nrf52. I've never done this before and Its been hard to find good resources online on the topic so if anyone here has any previous...
I am developing connection between BM833AF Evaluation board and nRF52840, Like a BLE Tag and Beacon. Need support in connection and transmitting data from one to another?...
Hi,
My use case is I have an RGB LED that I want to be green for normal operation, but blink red for 0.5s when a serial driver error occurs.
R, G, and B are each attached...
Hello,
I have multiple questions regarding BL mesh using nRF5 SDK for Mesh v4.2.0
1) is it possible to run this example using 2x NRF52840 dongles(PCA10059) and one NRF52840...
Hello
We have an application that ADV every second and is based on SDK 14.
We are currently attempting to move to SDK 17. What I have noticed is that if I change and...
HI,
I want to use nrf52833 for receiving SAADC DATA in my phone by using BLE_NUS_DATA_SEND.
Here are my codes.
In 716 ~ 724 lines, I added codes about BLE_NUS_DATA_SEND...
Hello
I'm using the nrf52840 DK with sdk version of 15.0.0.
My requirement is to flash my project through cli commands, so I have followed the following steps in below...
Hi,
I recently updated my toolchain using the nRFConnect tool chain manager.
(I was seeing problems after an OS update)
This update fixed my problem but when I build...
Hi,
Please, what are the settings for gpio driver in sdk15.2. for some gpio pin to be able to sink current (to act as gnd? ). In my project it is used for loadswitch enable...
Hi,
I have bumped into this bug in SDK v17.0.0 and SDK v17.0.2 but no fix yet.
We are using nRF52840 with S140.
Can you please make sure to release this fix asap because...
Hi There - My question is about the nrf5340 dual core cpu. I’d like to know if it is possible to have one core polling sensors on the spi bus - then pass this data to the...
Hello
I am testing sending the value to the app through the ble_app_uart of SDK v17.
I know roughly that I need to use 'ble_nus_data_send', but it is not printed from...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever. But I still got an err_code NRF_ERROR_INVALID_DATA. Softdevice is...
Hello,
I want to compile the "pca10040" template after installing the SDK and the command line tools with Segger Embedded Studio, but I got the error:
cannot find ......
