My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
When the macro NRF_SDH_BLE_GATT_MAX_MTU_SIZE is changed in the sdk_config.h file of any example from the ble_peripheral folder, the slave sends the message Exchange MTU Request...
Hi,
I am using nrf mesh sdk 3.1.0. with nrf52832.
For iv update one condition is iv_timeout_limit_passed(m_net_state.iv_update.timeout_counter). The timeout_counter value...
Hi,
I am evaluating ble peripheral with nRF52840 SDK 16 and SoftDevice s140 on windows 10.
The SDK is copied at location: C:\Nordic_Semi\nRF5SDK160098a08e2\
The SoftDEvice...
Hello,
I am not able to connect the dots. After setting up the beacons, ( adopted ble_beacon_app from Sdk 16 ) how can I perform localization algorithm ( trilateration)...
Hello. I try to configure radio at NRF52811 to prepare antenna switching and get correct I/Q samples from different antennas. I have 2 antennas that are 6 cm apart from one...
hello, I try to make an application with 6 different services. I used the ble_custom_service tutorial to create my different services.
I manage to work without problems...
Hi,
I am working with the bsp.c functions. One of the actions is BSP_BUTTON_ACTION_PUSH, which the value is 1. I would like to know at which electrical signal it is related...
Hello All, I am having a trouble with the nReset Pin during Deep Sleep. The issue is that the board is waking up from Deep Sleep due to floating nReset Pin. I am using a nrf52480...
Hi,
I am currently working on a product based on an nRF52832 (SDK 15.3, S112 6.1).
The firmware uses the Nordic UART Service to receive and send data from and to a smartphone...
I'm working on a new nRF5340 project where this will be the main application processor. The target system will support a large variety of sensors, and we expect to use a very...
Dear All,
We have designed our custom board based on BMD-330 (nRF52810 chipset). It uses i2c (TWI) to communicate with Azoteq IQS620A sensor .
TWI code runs fine on nRF52...
Hello there. I have few questions about nrf9160 GNSS part. Seems NRF have implemented own GPS L1 C/A correlator, current quality is not impressive at this moment, but approach...
Hello
In the radio test we can set up to 80 channels.
But isn't the table for the channel as follows?
40 channels is 2480MHz, right? What is the frequency of 80...
Hello
we are working on Audio project with nRF52840 include (microphone and Audio Amp). we used one I2S interface for Audio Amplifier but for Microphone we are confused...
